新村大橋T梁預應力施工方案.dwg
進入下載頁
新村大橋T梁預應力施工方案
一、 概述
新村大橋T梁長度為30m，預應力張拉采用標準號ASTM A416-98，270級，公稱直徑15.24mm，標準強度1860MPa的低松弛預應力鋼絞線做為預應力鋼束，鋼絞線松弛率為1.15%，錨具為15-6，15-5，15-3型群錨體系，采用波紋管預埋制孔。
二、 預應力鋼絞線制作
（1） 鋼絞線的運輸及保管
預應力鋼絞線在運輸中或現場使用，應避免造成局部彎曲和折傷，不得拋扔或拖卷材。
現場保管時，下面應墊上石子或方木，上面覆蓋雨布防腐蝕。
（2） 鋼絞線開盤
鋼絞線呈圓盤狀運至現場后，先平置在石子墊層木制墊柜上以防泥土、水對鋼絞線的腐蝕，四周用直徑為5cm的鋼管將鋼絞線固定，以防拉出散亂，扭曲和傷人。打開鋼絞線外包裝，抽出鋼絞線線頭，抽拉時，一邊拉，一邊放松其扣，否則鋼絞線會亂盤，對于有缺陷的部分，必須處理。
（3） 鋼絞線的切割與編束
根據圖紙?jiān)O(shè)計尺寸，確定料長，采用砂輪鋸切斷，不得用電弧切割。同一根鋼絞線不得焊縫接頭，同管道內
Village prestressed beam bridge construction program T
I. Introduction
Village Bridge T Beam length is 30m, prestressed tension of a standard No. ASTM A416-98, 270 level, the nominal diameter of 15.24mm, Standard strength 1860MPa low relaxation prestressed concrete strand as the prestressed steel strand relaxation rate of 1.15%, anchor bolt system for the 15-6,15-5,15-3 type group using the corrugated pipe embedded system holes.
Second, production of prestressed steel strand
(1) strand of the Transport and storage
Prestressed steel strand in the transport or field use, should be bent and folded to avoid local injury, may not throw or toss drag sheet.
On-site storage, the following should be mat side stones or wood, covered with rain deployed corrosion.
(2) strand opening
Strand cylindrical discoid transported to the scene, the first flat stones placed in the wooden cushion pad cabinet to prevent soil, water, corrosion of the steel strand, around the pipe with a diameter of 5cm will strand fixed, to prevent Pull out the scattered, twisted and wounding. Open the outer strand, strand out of thread, pull, the side pull, while easing the buckle, or strand people would drive for a defective part, must be addressed.
(3) strand of the cutting beam and compiled
According to the design size drawings to determine the expected length, with wheel saw cut, not cut with the arc. No weld joints with a steel wire, with the pipeline